Black Box IC109A-R2 Manual de instalación Pagina 49
- Pagina / 164
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
43
1
© 2007 Schneider Electric. All Rights Reserved.
63230-216-229-B1
Installation
Voltage Transformers
DANGER
Assembly
1 Insert the three connector pins into the slots on the
base unit.
2 Rotate connector to plug it into the 9-pin SUB-D
connector
3 Tighten the mounting screw .
HAZARD OF ELECTRIC SHOCK, EXPLOSION,
OR ARC FLASH
b Only qualified electrical workers should
install this equipment. Such work should
be performed only after reading this entire
set of instructions.
b NEVER work alone.
b Before performing visual inspections, tests,
or maintenance on this equipment,
disconnect all sources of electric power.
Assume that all circuits are live until they
have been completely de-energized,
tested, and tagged. Pay particular
attention to the design of the power
system. Consider all sources of power,
including the possibility of backfeeding.
b Always use a properly rated voltage
sensing device to confirm that all power is
off.
b Start by connecting the device to the
protective ground and to the functional
ground.
b Tighten all terminal screws, even those not
in use.
Failure to follow these instructions will result
in death or serious injury.
DE80104
DE80105
Connection
Make the connections to the screw-type connectors on the rear panel of the CCT640
(item above).
Wiring without Fittings
b One wire with maximum cross-section 0.2 to 2.5 mm² (
≤• AWG 24-12) or two
wires with maximum cross-section 0.2 to 1 mm² (
≥ AWG 24-16)
b Stripped length: 8 to 10 mm (0.31 to 0.39 in)
Wiring with Fittings
Recommended wiring with Telemecanique fittings:
b DZ5CE015D for one 1.5 mm² wire (AWG 16)
b DZ5CE025D for one 2.5 mm² wire (AWG 12)
b AZ5DE010D for two 1 mm² wires (AWG 18)
b Tube length: 8.2 mm (0.32 in)
b Stripped length: 8 mm (0.31 in)
b Tightening torque: 6.1 to 8.8 in-lb (0.7 to 1 Nm)
Grounding
The CCT640 must be grounded by connection (green/yellow wire and ring lug) to the
screw This is a safety measure in case the CCT640 disconnects.
* Detection of Plugged Connector (required for proper operation. Installed manually)
1
2
c
b
a
V‘cn
V‘bn
V‘an
V‘r
3
4
- Series 80 1
- Protective Relays 1
- Safety Instructions 0 3
- Safety Instructions 8
- Before You Begin 8
- Introduction 10
- Modular Architecture 10
- Selection Table 11
- Technical Characteristics 13
- Environmental Characteristics 14
- Precautions 15
- Equipment Identification 16
- Main Units 18
- Accessories 19
- Replacement Equipment 20
- Base Unit 21
- Dimensions 21
- Mounting 22
- Connection 23
- Installing Terminal Guard 24
- Typical for Series 80 24
- CAUTION DANGER 25
- Installation 26
- Sepam™ B83 Connection Diagram 27
- Sepam™ C86 Connection Diagram 28
- Input for Sepam™ B80 34
- Connected Voltage Inputs 35
- 1A/5A Current Transformers 36
- Test Accessories 40
- CSH120 & CSH200 42
- Zero Sequence CT 42
- CSH30 Interposing Ring CT 44
- ACE990 Zero Sequence 47
- CT Interface 47
- Voltage Transformers 48
- MES120, MES120G, MES120H 50
- 14 Input/6 Output Modules 50
- Remote Modules 53
- MET1482 54
- Temperature Sensor Module 54
- Analog Output Module 56
- Remote Advanced UMI Module 58
- Sync-Check Module 60
- Communication Accessory 64
- Selection Guide 64
- Connection of Communication 65
- ACE937 Fiber Optic Interface 68
- ACE969TP and ACE969FO 69
- Multi-Protocol Interfaces 69
- Description 71
- RS232/RS485 Converter 74
- ACE919CA and ACE919CC 76
- RS485/RS485 Converters 76
- Communications Wiring 78
- Cable Pinouts 81
- Network Limits 82
- User-Machine Interfaces (UMI) 84
- User-Machine Interfaces 85
- DAMAGE TO CARTRIDGE 86
- CAUTION 87
- Local Operation on the UMI 88
- Password 91
- Settings 93
- SFT2841 Setup and Operating 96
- Welcome Window 96
- Connection Window 97
- SFT2841 Set Up and Operating 100
- Software 100
- General Screen Organization 100
- Using the Software 101
- Creating User Messages 102
- Disturbance Recording 103
- Logic-Equation Editing 104
- Program 105
- Default Settings 107
- Configuring Sepam™ 109
- SFT2841 Software 113
- Mimic-Diagram Editor 113
- Presentation 113
- Contents 123
- Principles 124
- Commissioning 125
- Equipment 126
- General Examination and 127
- Preliminary Actions 127
- Checking Input Connections 129
- 3-Phase Generator 129
- Single-Phase Generator & 130
- Voltages Delivered by 3 VT 130
- Checking Phase Current 132
- Input Connections 132
- For Differential Applications 132
- LPCT Type Current Sensors 133
- Checking Residual Current/ 134
- Voltage Input Connections 134
- Checking Residual Current 135
- Van = Vr 135
- Checking Residual Voltage 136
- Broken Delta Arrangement 136
- With Voltage Delivered by 137
- 1 Neutral Point VT 137
- Checking Sepam™ B80 138
- Additional Voltage 138
- Additional Voltage 139
- Checking Sepam™ B83 140
- Additional Phase Voltage 140
- Additional Residual Voltage 142
- Checking Sepam™ C86 143
- Unbalance Current 143
- Checking Logic Input & 144
- Output Connections 144
- Checking Optional 145
- Module Connections 145
- Validating the Complete 146
- Protection Chain 146
- Test Sheet 147
- Sepam™ Series 80 147
- Troubleshooting Assistance 152
- 152
- Replacing the Base Unit 156
- Replacing the Battery 156
- 3-Wire Power System 158
- 4-Wire Power System 159
- 63230-216-229-B1 161
- Schneider Electric USA 164
© 2020, manymanuals.es. Todos los derechos reservados | 0.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales