Black Box IC109A-R2 Manual de instalación Pagina 154
- Pagina / 164
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
148
4
© 2007 Schneider Electric. All Rights Reserved.63230-216-229-B1
Maintenance
Troubleshooting Assistance
MINOR Fault: Sepam™ is operating in Downgraded Mode
b ON LED of UMI on in front
b LED of UMI flashing in front
b green LED on rear panel on
b red LED on rear panel flashing
PE50139
Inter-Module Link Fault
Possible Cause Action / Remedy
Faulty wiring Check remote module connections: RJ45
plugs of CCA77x cables clipped correctly into
sockets.
Fault message on display:
inter-module link fault
PE50139
Fault message on display:
MET1482 not available
MET1482 Module not Available
LEDs Possible Cause Action / Remedy
MET1482 Green and Red
LEDs off
Faulty wiring. Check module connections:
RJ45 plugs of CCA77x cables
clipped correctly into sockets.
MET1482 Green LED on
MET1482 Red LED off
No response from MET1482
module
Check the position of the
module number selection
jumper
b MET1 for first MET1482
module (temperatures T1
to T8)
b MET2 for second
MET1482 module
(temperatures T9 to T16).
b If the jumper position
needs to be changed,
reboot the MET1482
module by disconnecting
and reconnecting the
interconnection cord
MET1482 Red LED flashing. Faulty wiring, MET1482
powered but loss of dialogue
with base unit.
Check module connections:
RJ45 plugs of CCA77x cables
clipped correctly into sockets.
If the MET1482 module is the
last in the chain, make sure the
line terminating jumper is in
the Rc position.
In all other cases, the jumper
should be in the position
marked .
MET1482 Red LED on. More than three remote
modules connected to D1 or
D2 on base unit.
Distribute remote modules
between D1 and D2.
MET1482 module internal
fault.
Change MET1482 module.
PE50139
Fault message on display:
MSA141 not available
MSA141 Module Not Available
LEDs Possible Cause Action / Remedy
MSA141 Green and Red LEDs
off.
Faulty wiring, MSA141 not
powered.
Check module connections:
RJ45 plugs of CCA77x cables
clipped correctly into sockets.
MSA141 Green LED on.
MSA141 Red LED flashing.
Faulty wiring, MSA141
powered but loss of dialogue
with base unit.
Check module connections:
RJ45 plugs of CCA77x cables
clipped correctly into sockets.
If the MSA141 module is the
last in the chain, check that the
line terminating jumper is in
the Rc position.
In all other cases, the jumper
should be in the position
marked .
MSA141 Red LED on. More than three remote
modules connected to D1 or
D2 on base unit.
Distribute remote modules
between D1 and D2.
MSA141 module internal fault. Change MSA141 module.
2
3
Rc
4
Rc
- Series 80 1
- Protective Relays 1
- Safety Instructions 0 3
- Safety Instructions 8
- Before You Begin 8
- Introduction 10
- Modular Architecture 10
- Selection Table 11
- Technical Characteristics 13
- Environmental Characteristics 14
- Precautions 15
- Equipment Identification 16
- Main Units 18
- Accessories 19
- Replacement Equipment 20
- Base Unit 21
- Dimensions 21
- Mounting 22
- Connection 23
- Installing Terminal Guard 24
- Typical for Series 80 24
- CAUTION DANGER 25
- Installation 26
- Sepam™ B83 Connection Diagram 27
- Sepam™ C86 Connection Diagram 28
- Input for Sepam™ B80 34
- Connected Voltage Inputs 35
- 1A/5A Current Transformers 36
- Test Accessories 40
- CSH120 & CSH200 42
- Zero Sequence CT 42
- CSH30 Interposing Ring CT 44
- ACE990 Zero Sequence 47
- CT Interface 47
- Voltage Transformers 48
- MES120, MES120G, MES120H 50
- 14 Input/6 Output Modules 50
- Remote Modules 53
- MET1482 54
- Temperature Sensor Module 54
- Analog Output Module 56
- Remote Advanced UMI Module 58
- Sync-Check Module 60
- Communication Accessory 64
- Selection Guide 64
- Connection of Communication 65
- ACE937 Fiber Optic Interface 68
- ACE969TP and ACE969FO 69
- Multi-Protocol Interfaces 69
- Description 71
- RS232/RS485 Converter 74
- ACE919CA and ACE919CC 76
- RS485/RS485 Converters 76
- Communications Wiring 78
- Cable Pinouts 81
- Network Limits 82
- User-Machine Interfaces (UMI) 84
- User-Machine Interfaces 85
- DAMAGE TO CARTRIDGE 86
- CAUTION 87
- Local Operation on the UMI 88
- Password 91
- Settings 93
- SFT2841 Setup and Operating 96
- Welcome Window 96
- Connection Window 97
- SFT2841 Set Up and Operating 100
- Software 100
- General Screen Organization 100
- Using the Software 101
- Creating User Messages 102
- Disturbance Recording 103
- Logic-Equation Editing 104
- Program 105
- Default Settings 107
- Configuring Sepam™ 109
- SFT2841 Software 113
- Mimic-Diagram Editor 113
- Presentation 113
- Contents 123
- Principles 124
- Commissioning 125
- Equipment 126
- General Examination and 127
- Preliminary Actions 127
- Checking Input Connections 129
- 3-Phase Generator 129
- Single-Phase Generator & 130
- Voltages Delivered by 3 VT 130
- Checking Phase Current 132
- Input Connections 132
- For Differential Applications 132
- LPCT Type Current Sensors 133
- Checking Residual Current/ 134
- Voltage Input Connections 134
- Checking Residual Current 135
- Van = Vr 135
- Checking Residual Voltage 136
- Broken Delta Arrangement 136
- With Voltage Delivered by 137
- 1 Neutral Point VT 137
- Checking Sepam™ B80 138
- Additional Voltage 138
- Additional Voltage 139
- Checking Sepam™ B83 140
- Additional Phase Voltage 140
- Additional Residual Voltage 142
- Checking Sepam™ C86 143
- Unbalance Current 143
- Checking Logic Input & 144
- Output Connections 144
- Checking Optional 145
- Module Connections 145
- Validating the Complete 146
- Protection Chain 146
- Test Sheet 147
- Sepam™ Series 80 147
- Troubleshooting Assistance 152
- 152
- Replacing the Base Unit 156
- Replacing the Battery 156
- 3-Wire Power System 158
- 4-Wire Power System 159
- 63230-216-229-B1 161
- Schneider Electric USA 164
© 2020, manymanuals.es. Todos los derechos reservados | 0.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales