Black Box IC109A-R2 Manual de instalación Pagina 126
- Pagina / 164
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
120
3
© 2007 Schneider Electric. All Rights Reserved.63230-216-229-B1
Commissioning
Required Testing and Metering
Equipment
Generators
The AC and DC Generators have the following characteristics:
b dual sinusoidal AC current and voltage generator:
v 50 or 60 Hz frequency (according to the country)
v current adjustable up to at least 5 A rms
v adjustable up to the rated secondary phase-to-phase voltage of the VTs
v adjustable relative phase displacement (V, I)
v three-phase or single-phase type
b DC voltage generator:
v adjustable from 48 to 250 V DC, for adaptation to the voltage level of the
logic input being tested
Accessories
The following accessories come with the metering and testing equipment:
b plug with cord to match the "current" test terminal box installed
b plug with cord to match the "voltage" test terminal box installed
b electric cord with clamps, wire grip or touch probes
Metering Devices (part of the generator or separate)
b 1 ammeter, 0 to 5 A rms
b 1 voltmeter, 0 to 230 V rms
b 1 phasemeter, if phase displacement (V, I) is not identified on the voltage and
current generator
Computer Equipment
b PC with minimal configuration:
v Microsoft Windows 98 / NT4.0 / 2000 / XP
v 133 MHz Pentium processor
v 64 MB of RAM (32 MB with Windows 98)
v 64 MB free on hard disk
v CD-ROM drive
v One serieal port (or USB port with serial converter)
b SFT2841 software
b CCA783 serial connection cord between the PC and Sepam™
Documents
b complete connection diagram of Sepam™ and additional modules, with:
v phase current input connections to the corresponding CTs via the test
terminal box
v residual current input connection
v phase voltage input connections to the corresponding VTs via the test
terminal box
v
residual voltage input connection to the corresponding VTs via the test
terminal box
v logic input and output connections
v temperature sensor connections
v analog output connection
v connection of the sync-check module
b hardware bill-of-materials (BOMs) and installation rules
b group of Sepam™ parameter and protection settings, available in paper format
(or setting files made with SFT2841 software)
- Series 80 1
- Protective Relays 1
- Safety Instructions 0 3
- Safety Instructions 8
- Before You Begin 8
- Introduction 10
- Modular Architecture 10
- Selection Table 11
- Technical Characteristics 13
- Environmental Characteristics 14
- Precautions 15
- Equipment Identification 16
- Main Units 18
- Accessories 19
- Replacement Equipment 20
- Base Unit 21
- Dimensions 21
- Mounting 22
- Connection 23
- Installing Terminal Guard 24
- Typical for Series 80 24
- CAUTION DANGER 25
- Installation 26
- Sepam™ B83 Connection Diagram 27
- Sepam™ C86 Connection Diagram 28
- Input for Sepam™ B80 34
- Connected Voltage Inputs 35
- 1A/5A Current Transformers 36
- Test Accessories 40
- CSH120 & CSH200 42
- Zero Sequence CT 42
- CSH30 Interposing Ring CT 44
- ACE990 Zero Sequence 47
- CT Interface 47
- Voltage Transformers 48
- MES120, MES120G, MES120H 50
- 14 Input/6 Output Modules 50
- Remote Modules 53
- MET1482 54
- Temperature Sensor Module 54
- Analog Output Module 56
- Remote Advanced UMI Module 58
- Sync-Check Module 60
- Communication Accessory 64
- Selection Guide 64
- Connection of Communication 65
- ACE937 Fiber Optic Interface 68
- ACE969TP and ACE969FO 69
- Multi-Protocol Interfaces 69
- Description 71
- RS232/RS485 Converter 74
- ACE919CA and ACE919CC 76
- RS485/RS485 Converters 76
- Communications Wiring 78
- Cable Pinouts 81
- Network Limits 82
- User-Machine Interfaces (UMI) 84
- User-Machine Interfaces 85
- DAMAGE TO CARTRIDGE 86
- CAUTION 87
- Local Operation on the UMI 88
- Password 91
- Settings 93
- SFT2841 Setup and Operating 96
- Welcome Window 96
- Connection Window 97
- SFT2841 Set Up and Operating 100
- Software 100
- General Screen Organization 100
- Using the Software 101
- Creating User Messages 102
- Disturbance Recording 103
- Logic-Equation Editing 104
- Program 105
- Default Settings 107
- Configuring Sepam™ 109
- SFT2841 Software 113
- Mimic-Diagram Editor 113
- Presentation 113
- Contents 123
- Principles 124
- Commissioning 125
- Equipment 126
- General Examination and 127
- Preliminary Actions 127
- Checking Input Connections 129
- 3-Phase Generator 129
- Single-Phase Generator & 130
- Voltages Delivered by 3 VT 130
- Checking Phase Current 132
- Input Connections 132
- For Differential Applications 132
- LPCT Type Current Sensors 133
- Checking Residual Current/ 134
- Voltage Input Connections 134
- Checking Residual Current 135
- Van = Vr 135
- Checking Residual Voltage 136
- Broken Delta Arrangement 136
- With Voltage Delivered by 137
- 1 Neutral Point VT 137
- Checking Sepam™ B80 138
- Additional Voltage 138
- Additional Voltage 139
- Checking Sepam™ B83 140
- Additional Phase Voltage 140
- Additional Residual Voltage 142
- Checking Sepam™ C86 143
- Unbalance Current 143
- Checking Logic Input & 144
- Output Connections 144
- Checking Optional 145
- Module Connections 145
- Validating the Complete 146
- Protection Chain 146
- Test Sheet 147
- Sepam™ Series 80 147
- Troubleshooting Assistance 152
- 152
- Replacing the Base Unit 156
- Replacing the Battery 156
- 3-Wire Power System 158
- 4-Wire Power System 159
- 63230-216-229-B1 161
- Schneider Electric USA 164
© 2020, manymanuals.es. Todos los derechos reservados | 0.062 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales