Black Box IC109A-R2 Manual de instalación Pagina 105
- Pagina / 164
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
9963230-216-229-B1
2
© 2007 Schneider Electric. All Rights Reserved.
Use
SFT2841 Setting and Operating
Software
Setting Up and Operating a Logipam
Program
PE50429
Presentation
The Logipam screen in the SFT2841 software is used to:
b link a Logipam program to the configuration of a Sepam™
b set program parameters
b view the internal program variables to assist in program set-up
Note: Use the SFT2885 software to first enter and confirm Logipam.
Press to access the Logipam screen.
The Logipam screen is accessed in Connected mode with a Sepam™ if it has the
Logipam SFT080 option. In disconnected mode, the Logipam screen is still
accessible, but the configuration files containing a Logipam program are loaded
exclusively to Sepam™ units with the SFT080 option.
The Logipam screen has five tabs:
b Logipam: selection of the program and its operating mode
b Internal bits: view the internal bits and set the configuration bits
b Counters: view the current value and set the counters
b Delays: set time delays
b Clocks: set the clocks
Linking Logipam to a Sepam™ Configuration
Logipam links to a Sepam™ configuration by selecting the program file. Use the
Select button on the Logipam tab sheet.
The programs are stored in the Logipam subdirectory of the SFT2841 installation
directory (by default C:\Program Files\Schneider\SFT2841\Logipam). They have the
extension *.bin.
Once the program has been selected, the program properties display (name,
version, author, installation characteristics, etc.).
The "Apply" Button
In Disconnected mode, the Apply button stores the name of the Logipam program
in the Sepam™ configuration file. The program is then loaded in Sepam™ at the
same time as the configuration file.
In Connected mode, it stores the name of the Logipam program in the Sepam™
configuration file and loads the program in Sepam™.
The Delete Button
The Delete button eliminates the link between the Logipam program and the
configuration file. In Connected mode, the name of the Logipam program is deleted
in the Sepam™ memory cartridge when the Apply button is clicked.
Selecting the operating mode of Logipam:
b On: the program runs immediately after it is loaded
b Off: the program does not run and program outputs remain set to 0
You can also temporarily postpone Logipam program processing if the program has
not been fully set up.
Logipam screen.
- Series 80 1
- Protective Relays 1
- Safety Instructions 0 3
- Safety Instructions 8
- Before You Begin 8
- Introduction 10
- Modular Architecture 10
- Selection Table 11
- Technical Characteristics 13
- Environmental Characteristics 14
- Precautions 15
- Equipment Identification 16
- Main Units 18
- Accessories 19
- Replacement Equipment 20
- Base Unit 21
- Dimensions 21
- Mounting 22
- Connection 23
- Installing Terminal Guard 24
- Typical for Series 80 24
- CAUTION DANGER 25
- Installation 26
- Sepam™ B83 Connection Diagram 27
- Sepam™ C86 Connection Diagram 28
- Input for Sepam™ B80 34
- Connected Voltage Inputs 35
- 1A/5A Current Transformers 36
- Test Accessories 40
- CSH120 & CSH200 42
- Zero Sequence CT 42
- CSH30 Interposing Ring CT 44
- ACE990 Zero Sequence 47
- CT Interface 47
- Voltage Transformers 48
- MES120, MES120G, MES120H 50
- 14 Input/6 Output Modules 50
- Remote Modules 53
- MET1482 54
- Temperature Sensor Module 54
- Analog Output Module 56
- Remote Advanced UMI Module 58
- Sync-Check Module 60
- Communication Accessory 64
- Selection Guide 64
- Connection of Communication 65
- ACE937 Fiber Optic Interface 68
- ACE969TP and ACE969FO 69
- Multi-Protocol Interfaces 69
- Description 71
- RS232/RS485 Converter 74
- ACE919CA and ACE919CC 76
- RS485/RS485 Converters 76
- Communications Wiring 78
- Cable Pinouts 81
- Network Limits 82
- User-Machine Interfaces (UMI) 84
- User-Machine Interfaces 85
- DAMAGE TO CARTRIDGE 86
- CAUTION 87
- Local Operation on the UMI 88
- Password 91
- Settings 93
- SFT2841 Setup and Operating 96
- Welcome Window 96
- Connection Window 97
- SFT2841 Set Up and Operating 100
- Software 100
- General Screen Organization 100
- Using the Software 101
- Creating User Messages 102
- Disturbance Recording 103
- Logic-Equation Editing 104
- Program 105
- Default Settings 107
- Configuring Sepam™ 109
- SFT2841 Software 113
- Mimic-Diagram Editor 113
- Presentation 113
- Contents 123
- Principles 124
- Commissioning 125
- Equipment 126
- General Examination and 127
- Preliminary Actions 127
- Checking Input Connections 129
- 3-Phase Generator 129
- Single-Phase Generator & 130
- Voltages Delivered by 3 VT 130
- Checking Phase Current 132
- Input Connections 132
- For Differential Applications 132
- LPCT Type Current Sensors 133
- Checking Residual Current/ 134
- Voltage Input Connections 134
- Checking Residual Current 135
- Van = Vr 135
- Checking Residual Voltage 136
- Broken Delta Arrangement 136
- With Voltage Delivered by 137
- 1 Neutral Point VT 137
- Checking Sepam™ B80 138
- Additional Voltage 138
- Additional Voltage 139
- Checking Sepam™ B83 140
- Additional Phase Voltage 140
- Additional Residual Voltage 142
- Checking Sepam™ C86 143
- Unbalance Current 143
- Checking Logic Input & 144
- Output Connections 144
- Checking Optional 145
- Module Connections 145
- Validating the Complete 146
- Protection Chain 146
- Test Sheet 147
- Sepam™ Series 80 147
- Troubleshooting Assistance 152
- 152
- Replacing the Base Unit 156
- Replacing the Battery 156
- 3-Wire Power System 158
- 4-Wire Power System 159
- 63230-216-229-B1 161
- Schneider Electric USA 164
© 2020, manymanuals.es. Todos los derechos reservados | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales