Black Box AC2000A Especificaciones descargar pdf (Pagina 7)

HOW TO USE THE BONUS TABLE

Think of the bonus table as the total amount of EXTRA tokens

after the regular payout, that you wish to receive:

EXAMPLE: PAYOUT: 4 tokens for $1, 24 for a $5, 52 for a $10,

120 for a $20.

24 tokens = $1 extra in tokens

52 tokens = $3 extra in tokens

120 tkns = $10 extra in tokens.

Now go to the bonus table, find where the $5 column =$1

Look over to the $10 and go down until you see $3.

Finally go to the $20 column to where = $10.

You should be at 1-3-7; Turn “ON” your right dipswitches 1-3-7

to set this payout.

DIPSWITCHES

The following table shows how to set the dip switches to your

desired payout.

“ON” COINS PER DOLLAR

#1 1

#2 2

#3 4

#4 8

The left DipSwitch controls the left hopper’s pay out and the

right DipSwitch controls the right hopper’s pay out.

Refer to the next table to set up your changer for the settings you

need.

MODE DESCRIPTIONS

Some of the modes are self-explanatory while others have

sub modes built into the chip. Here is a list of the modes

and sub modes when applicable.

MODE 2 - $1 coins the balance in quarters:

The quarters for each bill are controlled by the sub mode

settings of the right dipswitches #1 & #2.

Neither “ON” – 16 Quarters balance in $1 coins.

#1 “ON” only – 8 Quarters balance in $1 coins.

#2 “ON” only – 12 Quarters balance in $1 coins.

#1 & #2 “ON” – 4 Quarters balance in $1 coins.

MODES’ #5 & #11 – Setting right dips in “$1

increments”:

Refer to Page 6 Under “Dipswitches Cont.”. But instead

of counting up in coins, think of it as dollars.

MODE #14 – Canadian $1 &$2 coin payout:

The right dipswitches #1 & #2 can alter the amount of $1

coins given to each denomination.

Luni’s per $ $5 $10 $20

Neither “ON” - 1L 0L 0L

#1 “ON” 3L 2L 2L

#2 “ON” 3L 4L 4L

The machine will always give 2 Luni’s for a Tuni.

FUSE

High voltage fuse: This is the primary transformer AC fuse

for the main logic board and the validator. Any direct short

of the Transformer or validator will cause this fuse to blow.

Replace this fuse with a 2-½ amp AS fuse only.

REPLACING THIS FUSE WITH ANYTHING OTHER

THAN A 2 ½ AMP “GDC” MAY RESULT IN A FIRE OR

AN UNSAFE WORKING CONDITION!! (See fig. 1 for

location of this fuse.)

Indicator Lights

Main Logic Board:

1. Green LED on: AC power applied to the logic board, all

fuses are good.

2. Decimal Point & Red LED:

A. Heartbeat - 5 and 12vdc present. The changer is in

standby waiting for a bill pulse.

B. On Steady - Out of service, Hopper error detected.

Validator logic board:

1. Red LED

A. On Steady - Standby Mode, waiting for bill

insertion.

B. Flashing - Error mode, go to page for error code

information.

C. Off - The changer “Empty” LED is lit.

WIRE HARNESS COLOR AND DEFINITIONS

Validator harness:

Red - Switched Hot 120VAC

White - Neutral 120VAC

Black - 120VAC Low current validator enable

Yellow - +5vdc credit pulse line

Blue - -5vdc credit pulse line

Orange - +12vdc Empty LED

Brown - -12vdc Empty LED

Hopper Harness

Gray - Coin counting optic status line

White - Low coin sense (+5vdc)

Green - Coin counting optic pay out feedback line

Yellow - Raw sensor output line

Purple - Hopper pay out line from main logic board (+)

Brown - Hopper pay out line from main logic board (-)

Red - +12vdc logic board supply voltage

Black(s) -12v, 24v low coin sense ground

Orange - +24vdc Motor supply voltage

1 2 3 4 5 6 7 8 9 10 11 12 ... 44 45

Comentarios a estos manuales

Sin comentarios

Black Box AC2000A Especificaciones Pagina 7

Comentarios a estos manuales

Relacionado con productos y manuales para No Black Box AC2000A