Black Box AC2000A Especificaciones descargar pdf (Pagina 4)

cord is not rubbing against any sharp edges or is being

strained in any way. Then mount the line cord clamp to

the studs at the hole. Tighten securely. Installation is

finished and you can proceed to the “Filling the

Hopper” section.

18. In order to continue you will need to purchase electrical

cable conduit, a standard 3-prong AC wall outlet and 12-

gauge wire. We highly recommend HIRING a qualified

electrician to perform the following!

A. Install the conduit box on the conduit entering the

cabinet in the lower right side of the cabinet.

B. Secure the 3 wires (hot, neutral, and ground) to the AC

wall outlet and the ground wire should also be directly

attached to the cabinet ground terminal.

C. Connect the AC line cord into the bottom of the main

logic board.

D. Plug the male end into the AC outlet just installed.

E. Properly fold the line cord to avoid sharp corners and any

other damage.

Proceed to the “Filling the Hoppers” section.

FILLING THE HOPPERS

When each hoppers has less than 80 - 100 coins left the red

“Empty” LED will light on the front of the changer. If you

have disconnected your LED make sure the orange wire is

going to the terminal on the LED that has the red wired

terminal. Whenever the “Empty” LED is “ON” the

validator is disabled and it will no longer accept bills.

1. Turn OFF the power on the main logic board.

2. Slide the hoppers out from the cabinet and insert the

coins through the opening on the top. There must be at

least enough coins to cover the two gold plates at the

bottom of the hoppers. (Somewhere between 160 and

1600 coins minimum to maximum.)

3. Slide the hoppers back into the hopper plate. Do not

use excessive force!

4. Turn “ON” the power switch. The “Empty” LED is

now off and the bill validator is ready to accept bills.

USING THE DUMP MODE TO EMPTY THE

HOPPERS

1. Open the cabinet door.

2. Turn OFF the POWER switch.

3. Place a suitable container in front of the hoppers to

catch the coins.

4. Press and hold the “DUMP” button on the upper right

corner of the Main Logic Board. Turn ON the Power

switch. The red LED numbers on the main logic board

will come on all “00000’s”. Once the red “00000’s”

lights up the SECOND time, release the “DUMP”

button. If it is not released within one second, the

“DUMP” mode is canceled as a security feature.

5. The hoppers will dispense coins until the POWER

switch is turned OFF. If the red LED numbers are not

counting up rapidly on the Main Logic Board’s display

the dump mode was not accessed. Please try again.

THE DIP SWITCHES

The 2000/2001 series changer is capable of dispensing coins

in many different pay out modes. Setting the coins out per

dollar is controlled by which Dipswitches turned “ON."

(Refer to figure 1 for their location.) For example, switch #2

is “ON” on both dipswitches; therefor the payout equals 4

coins per dollar. Two coins per hopper for one dollar.

FIGURE 2

(THIS IS NOT THE DIPSWITCH BANK FOR SETTING

THE BILL DENOMINATIONS.

(For those dip switches go to page 13-14.)

1 2 3 4 5 6 7 8

VALIDATOR

CONNECTOR

MAIN LOGIC BOARD

BILL

METER

ON/OFF

SWITCH

EPROM

CHIP

ure

PRIMARY

2-1/2 AMP

FUSE

DUMP

BUTTON

TRANSFORMER

HOPPERS

HARNESS

CONNECTORS

DIP

SWITCHES

AC LINE

CORD INPUT

1 2 3 4 5 6 7 8 9 ... 44 45

Comentarios a estos manuales

Sin comentarios

Black Box AC2000A Especificaciones Pagina 4

Comentarios a estos manuales

Relacionado con productos y manuales para No Black Box AC2000A