Black Box KV150A-R2 Manual de usuario Pagina 148
- Pagina / 160
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
APPENDIX C: DIP-Switch Settings and Their Numeric Equivalents
147
Appendix C: DIP-Switch Settings
and Their Numeric Equivalents
Table C-1 on the next page is useful for two purposes:
1. If you need to override the physical setting of the DIP switch on the currently selected computer channel’s
CPU-Interface Card (see Section 4.2), you can issue the “<CM>SW=n[Enter]” command (see Section 8.14)
to do so, where n is the decimal number that equals the binary number that in turn corresponds to the
desired DIP-switch setting (1 = ON, 0 = OFF). For example, suppose the Card is currently set to translate
composite sync to H/V-sync for your monitor, to use a 1-second timeout, and to reverse the keyboard keys
when it maps. The DIP switch would read, from left to right (position 8 through position 1), “OFF OFF
OFF ON OFF OFF ON OFF”—00010010 binary. Now suppose you’ve swapped in a somewhat slower PC-
compatible computer that outputs sync on green, and you want to alter the Card’s DIP-switch setting so
that the Card translates sync on green to H/V-sync, uses a 10-second timeout, and does not reverse the
keyboard keys. If you had to manually reset the DIP switch, it would read “OFF OFF OFF OFF ON OFF
OFF ON”, 00001001 binary. Looking this up in Table C-1 shows you that this equals 9 decimal, so instead
of removing the Card and fussing with it, you can just send it the “<CM>SW=9[Enter]” command.
2. In a cascaded ServSwitch Multi system, all of the Expansion Transmit Cards in a given Switch must have
their DIP switches set to the same unit address, and this address must be unique to that Switch. So if you
want a new Switch you’re adding to the system to be unit 7, look up 7 decimal in Table C-1; it will show you
that you should set the DIP switch to 00000111 binary, which corresponds to (left to right—position 8
through position 1) “OFF OFF OFF OFF OFF ON ON ON.” Note that addresses 0 and 255 are reserved;
do not set the Card to these addresses.
- KV150A-R2 1
- KV160A-R2 1
- THE SERVSWITCH™ FAMILY 2
- FCC, IC, AND NOM STATEMENTS 4
- Contents 6
- Contents (cont’d) 7
- TABLE OF CONTENTS 10
- 1. Specifications 11
- CHAPTER 1: Specifications 12
- 2. Introduction 15
- 2.5 Safety Precautions 19
- CHAPTER 2: Introduction 20
- A B C D E F G H I J K L 21
- SELECTED 24
- B C D E F G H I J K L M N 24
- FAIL POWER 24
- 1 2 3 4 5 6 7 8 26
- ESCAPE ENTER 27
- IMPORTANT NOTE 28
- Server Cables, and Computers 38
- 8 7 6 5 4 3 2 1 40
- CAUTION! 41
- 5. Installing Management and 49
- Serial Control Cards and 49
- Associated Equipment 49
- 5.3 Installing the Cards 51
- 6. Planning and Installing an 53
- Expanded System (Optional) 53
- SWITCH 0 57
- SWITCH 1 57
- SWITCH 2 57
- Regular Transmit Card 59
- (KV1601C) 59
- CAT5 Transmit Card 59
- (KV1603C) 59
- 7. The ServSwitch Multi Hub 65
- Power/fan 66
- Transmit and Receive 66
- 7.2 Features and Benefits 67
- 7.3 Installing the Hub 67
- HE IDLE DISPLAY SCREEN 72
- HE CONTRAST SCREEN 73
- 7.6 Flash Upgrading 76
- X 128 MATRIX 77
- X 384 MATRIX 78
- X 256 MATRIX 79
- 8. Operation 80
- 8.2 Keyboard Control 82
- EYSTROKE NOTATION 82
- EYBOARD-BASED SWITCHING 82
- 8.3 Multiuser Operation 83
- See Section 4.2.3 86
- See Section 9.4.3.E 87
- 88
- 89
- 8.6 Channel Scanning 91
- 8.7 Broadcast Mode 92
- 8.9 Swap Mode 93
- 8.10 Privacy Mode 93
- 8.8 Follow Mode 93
- 8.11 Command Forwarding 94
- CHAPTER 8: Operation 100
- SERVSWITCH™ MULTI 101
- (UICD Consoles Only) 102
- 9.2 The On-Screen Menus 103
- HE CHANNEL-LIST MENU 103
- HE COMMAND-LINE-ENTRY WINDOW 107
- HANNEL-LIST MENU FUNCTIONS 108
- SER-LIST MENU FUNCTIONS 111
- (Command) key. But the 114
- Control Cards 116
- 10.3 The Main On-Screen Menus 118
- Open channels 120
- Active channel 120
- Cursor position 120
- Line in the Open Channel list 120
- (1 of 2 in this example) 120
- ISPLAY CHASSIS CONFIGURATION 123
- ISPLAY FLASH ROM STATUS 124
- EARCH FOR CONNECTED CHASSIS 127
- ET DATE AND TIME 127
- RANSFER SECURITY LOG 128
- RANSFER CHANNEL LIST 129
- Alert Message 130
- Active User List 130
- Log Window 130
- 11. Troubleshooting 133
- CHAPTER 11: Troubleshooting 134
- IDEO BLANKS OUT UNEXPECTEDLY 135
- EYBOARD DOESN’T WORK 135
- OUSE DOESN’T WORK 136
- ERIAL DEVICE DOESN’T WORK 136
- ICROPHONE DOESN’T WORK 137
- 11.2 Calling Black Box 138
- 11.3 Shipping and Packaging 138
- Appendix B: Problem Report 147
- Appendix D: Cables 150
- D.2 User Cables 151
- APPENDIX D: Cables 152
- D.3 Adapters 152
- Serial Connections 153
- Appendix F: 154
Relacionado con productos y manuales para Los componentes del chasis Black Box KV150A-R2
(32 paginas)US Robotics USR2450 manuels
Manuels d'utilisation et guides de l'utilisateur pour Non US Robotics USR2450.
Nous fournissons des manuels en pdf 1 US Robotics USR2450 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Comentarios a estos manuales